SN883RH2_SN890CH2(34).book 年7月8日 金曜日 午後6時1分 DRIVING FASTENERS NOTE: This tool is shipped with SINGLE ACTUATION selected. Check operation of the contact arm & trigger if moving smoothly. 1 2 3 4 5 6 7 8 9 Keep hands and body away from the discharge outlet when driving the fasteners because of dangerous of hitting the hands or body by mistake. BEFORE OPERATION Check the following prior operation. INSTRUCTIONS FOR OPERATION READ SECTION TITLED "SAFETY INSTRUCTIONS". Volatile fumes from these substances could be drawn into the compressor and compressed together with the air and this could result in an explosion. SN883RH2_SN890CH2(34).book 年7月8日 金曜日 午後6時1分 Thinner Air compressor Gasoline Regulator Air filter Oiler Air hose DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). Select the operating air pressure within this range for best fastener performance. WARNING RECOMMENDED OPERATING PRESSURE: READ SECTION TITLED "SAFETY INSTRUCTIONS" 70 to 100 p.s.i. The fitting must be capable of discharging tool air pressure when disconnected from the air supply. AIR SUPPLY AND CONNECTIONS TOOL AIR FITTINGS: This tool uses a 3/8" N.P.T. NAME OF PARTS 8 7 2 1 4 3 9 1 Frame 2 Cylinder Cap 3 Contact Arm 4 Nose 5 Magazine 6 5 0 6 Trigger 7 Grip 8 Exhaust Cover 9 Pusher 0 Adjustment Dial 2. DO NOT DRIVE FASTENERS ON TOP OF OTHER FASTENERS Driving fasteners on the top of other fasteners may cause deflection fasteners which could cause injury. NEVER ACTUATE THE TOOL INTO FREE SPACE This will avoid any hazard caused by free flying fasteners and excessive strain of the tool. NEVER USE THE TOOL IF ANY PORTION OF THE TOOL CONTROLS (e.g., TRIGGER, CONTACT ARM) IS INOPERABLE, DISCONNECTED, ALTERED OR NOT WOKING PROPERLY 21. Inspect to confirm that all screws and bolts are tight and properly installed prior to operating the tool. INSPECT SCREW TIGHTNESS Loose or improperly installed screws or bolts cause accidents and tool damage when the tool is put into operation. Be sure to use only specified fasteners when operating the tool. USE SPECIFIED FASTENERS (SEE PAGE 7) The use of fasteners other than specified fasteners will cause the tool malfunction. DO NOT OPERATE THE TOOL NEAR A FLAMMABLE SUBSTANCE Never operate the tool near a flammable substance (e.g., thinner, gasoline, etc.). SN883RH2_SN890CH2(34).book 年7月8日 金曜日 午後6時1分 NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection. CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. SN883RH2_SN890CH2(34).book 年7月8日 金曜日 午後6時1分 INDEX INDEX ÍNDICE ENGLISH FRANÇAIS ESPAÑOL Page 35 to 18 to 34 to 50 DEFINITIONS OF SIGNAL WORDS WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. SN883RH2_SN890CH2(34).book 年7月8日 金曜日 午後6時1分 SN883RH2 SN890CH2 PNEUMATIC NAILER CLOUEUSE PNEUMATIQUES CLAVADORAS NEUMATICAS PARA PEINES DE CLAVO SN883RH2 SN890CH2 OPERATING AND MAINTENANCE MANUAL MANUEL D'UTILISATION ET D'ENTRETIEN MANUAL DE OPERACIONES Y MANTENIMIENTO BEFORE USING THIS TOOL, STUDY THIS MANUAL TO ENSURE SAFETY WARNING AND INSTRUCTIONS.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |